-
Categories
HVAC Equipment & Parts
- Air Handlers
- Air-To-Water Heat Pumps
- Condensate Overflow Shut-off Switches
- Condensate Removal & Management
- Condenser Pads
- Condensers (Outdoor Units)
- E-Z Traps
- Electric Heat Kits
- Furnaces
- Gas Furnace and A/C Systems
- Gas-Fired Unit Heaters
- Geothermal Units
- Goodman Replacement Parts
- Heat Pumps
- Install & Duct Tape
- Installation Accessories
- Linesets
- Miscellaneous Supplies
- Mounting Brackets
- Mr. Cool Universal Series
- Packaged Units
- Portable AC and Heat Units
- Refrigerant Coils
- Secondary Drain Pans
- Service Parts
- Sheet Metal Duct & Fittings
- Surge Protection
- Thermostats and Thermostat Wire
- Through The Wall Units
- Window Units
- More categories
Mini-Splits & Accessories
- Concealed Indoor Units
- Ducted Air Handler
- Ducted Mini-Split Air Handler
- Ductless Accessories
- Electric Heater Module
- Indoor Ceiling Cassettes
- Indoor Wall Mounted
- Intelli-HEAT Coil
- Mini Split Wire & Cable
- Mini-Split Risers
- Mitsubishi Mini-Splits
- Mr. Cool Ductless Mini-Splits
- Outdoor Units, Multi-Zone
- Outdoor Units, Single-Zone
- ProFit Quick Connect Fittings
- More categories
Mitsubishi PAC-WHS01HCE Kumo Station™ for Kumo Cloud®
Mitsubishi PAC-WHS01HCE Kumo Station™ for Kumo Cloud®
General specs
- Product codePACWHS01HCE
- ManufacturerMitsubishi
- SKUPACWHS01HCE
Dimensions
- Dimensions2.38in x 5.97in x 12.06in
- Weight3.97lb
Mitsubishi PAC-WHS01HCE Kumo Station™ for Kumo Cloud®
General Features:
Emergency Operation Switches
Ability to override the output status of the 4 equipment controller outputs
Can open or close the contacts at channels 1, 2, 3, 4 to prohibit or permit operation
Auto mode will allow for remote setting of channels 1, 2, 3, 4
Channel selection
Able to be controlled through kumo cloud® app
- Requires kumo cloud app version 2.6 or later
Outdoor Air Temperature sensor optional
- If not supplied, defaults to heat pump and supplemental heat
- If fails, the system fails to heat pump and supplemental heat
Included: Recess panel allows for recessed installation. See instruction manual for more information.
Wiring and Settings Check
- Emergency Operations Check: Verifies the current setup will react according to user specifications in the event of an emergency
- Function Setting Switch Check: Verifies the kumo station™ switches operate according to the user specifications
- Communication Check
- Operation Check of Outdoor Air Temperature Sensor
Specifications:
4 channel equipment controller with outside air temperature monitoring
Manages and stages heat pump and third party supplemental heat
Setup available through kumo cloud® app
Communicates with other equipment wirelessly without internet connectivity
Able to connect non-powered and powered equipment
LED function settings
- Equipment communication
- Equipment status
Patent pending algorithm to control system changeover
- Reduces system changeover occurrence
- Can set priority zones
4 dry contact outputs
Minimum run time can be changed in 10 minute intervals to avoid frequent system changeovers
Compatible with Mitsubishi Electric CITY MULTI® units. Contact Mitsubishi Electric representative for more information.
Ambient temperature range from 32°F (0 °C) to 104°F (40 °C)
Maximum relative humidity 80%
Avoid installing in an area of direct sunlight or sources of heat
Must take into consideration other areas of electronic noise
Install indoors
Dimensions:
Product Height (in.): 12.0625”
Product Width (in.): 5.96875”
Product Depth (in.): 2.375”
Unit Weight: 3.97 lbs.